Recent Progress in Sludge-Derived Biochar and Its Role in Wastewater...

[Full title: Recent Progress in Sludge-Derived Biochar and Its Role in Wastewater Purification]

[Find the meaning and references behind the names: Yue, Change, Resources, Ideal, Doi, June, Basel, Act, Raw, Key, Gao, Fang, Urban, Paolo, Hao, Million, Trace, Matter, Development, Trend, Carbon, Steady, Edu, China, Large, Data, Under, Hand, Cakes, Zhu, High, Rise, Open, Energy, Progress, Zhou, Due, Role, April, Lower, Study, Goal, Strong, Serious, Peak, Need, Yang]

Citation: Zhou, Y.; Gao, J.; Yang, X.; Ni, H.; Qi, J.; Zhu, Z.; Yang, Y.; Fang, D.; Zhou, L.; Li, J. Recent Progress in Sludge-Derived Biochar and Its Role in Wastewater Purification Sustainability 2024 , 16 , 5012. https:// doi.org/10.3390/su 16125012 Academic Editor: Paolo S. Calabr ò Received: 23 April 2024 Revised: 29 May 2024 Accepted: 3 June 2024 Published: 12 June 2024 Copyright: © 2024 by the authors Licensee MDPI, Basel, Switzerland This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution (CC BY) license (https:// creativecommons.org/licenses/by/ 4.0/) sustainability Review Recent Progress in Sludge-Derived Biochar and Its Role in Wastewater Purification Yujun Zhou 1 , Jiamin Gao 1 , Xuran Yang 1 , Hao Ni 1 , Junwen Qi 1 , Zhigao Zhu 1 , Yue Yang 1 , Di Fang 2 , Lixiang Zhou 2 and Jiansheng Li 1, * 1 School of Environmental and Biological Engineering, Nanjing University of Science and Technology, Nanjing 210094, China; yjzhou@njust.edu.cn (Y.Z.); gaojiamin@njust.edu.cn (J.G.); xuran@njust.edu.cn (X.Y.); nihao 123@njust.edu.cn (H.N.); qijunwen@njust.edu.cn (J.Q.); zhuzhigao@njust.edu.cn (Z.Z.); yangyue 2022@njust.edu.cn (Y.Y.) 2 Department of Environmental Engineering, College of Resources and Environmental Sciences, Nanjing Agricultural University, Nanjing 210095, China; di.fang@njau.edu.cn (D.F.); lxzhou@njau.edu.cn (L.Z.) * Correspondence: lijsh@njust.edu.cn Abstract: As the by-product of wastewater treatment, a large amount of sludge is generated annually Turning this waste into a resource is a feasible and sustainable strategy to reduce potential environmental risks and recover energy. As a way to realize the international goal of carbon dioxide emission peak and carbon neutrality, producing biochar from sludge has gained worldwide attention This review evaluates recent progress in synthesis techniques for biochar of sludge origin. Different preparation techniques and their key affecting factors are compared and described. The obtained sludge-derived biochar could be employed for eliminating aqueous pollution or purifying wastewater, mainly through adsorption and catalytic reactions. The removal of various pollutants by sludgederived biochar and its related mechanisms are discussed and summarized in detail. This review will be conducive for a comprehensive understanding of recent progress in sludge-derived biochar study and for guiding the purposeful production of biochar, as well as for developing wastewater purification technology based on sludge-derived biochar Keywords: sludge; biochar; pyrolysis; wastewater; adsorption; advanced oxidation process 1. Introduction With accelerated urbanization and industrialization, the amount of sludge generated from municipal wastewater treatment plants (WWTPs) has increased significantly, which has led to serious environmental problems. According to data from the Ministry of Housing and Urban–Rural Development of China, in 2021 alone, the treatment capacity of municipal WWTPs in China reached 70.6 billion cubic meters, and the amount of sludge cakes with a moisture content of about 80% exceeded 56 million tons. With the steady growth in sewage treatment, the amount of sludge will continue to rise in the future. Sludge, as a by-product of the sewage treatment process, contains a variety of pollutants including pathogens, toxic organic chemicals, and heavy metals, which need to be treated appropriately [ 1 ]. On the other hand, sewage sludge can also act as a resource, for applications such as soil amendment, due to its high contents of organic matter, nutrients (e.g., N and P), and some trace elements. Thus, converting waste into resources for reuse is a future global trend For the purpose of realizing the goal of international “Carbon Dioxide Emission Peak” and “Carbon Neutrality”, producing biochar based on biomass waste and its utilization can lower the industry’s carbon footprint and mitigate the effects of climate change. Sludge is an ideal raw material for biochar manufacturing because of its intrinsic floc structure and richness in carbon and other reactive elements. Compared to conventional sludge treatment methods, including anaerobic digestion, composting, and incineration, producing biochar Sustainability 2024 , 16 , 5012. https://doi.org/10.3390/su 16125012 https://www.mdpi.com/journal/sustainability

[Find the meaning and references behind the names: Stage, Gas, Vary, Peer, Time, Modi, Bio, Deep, Web, Area, Evolution, Past, Oil, General, Good]

Sustainability 2024 , 16 , 5012 2 of 16 using sludge has gained increasing attention. As calculated and summarized in Figure 1 , publications focusing on biochar and sludge-derived biochar in the past decade have been increasing drastically. Transforming sludge into functional biochar is an environmentally friendly technique, which can not only remove hazardous compounds such as pathogens and organic pollutants from sludge and reduce the volume of sludge, but can also convert the organic matter in sludge into bio-oil and bio-gas, for use as fuels [ 2 ]. Meanwhile, the residual solid, which is called sludge-derived biochar, is proven to have a porous structure with a large specific surface area and abundant oxygen-containing functional groups with good metal-binding affinity, which can be further developed as adsorbents and catalysts [ 3 ]. This review provides a deep insight into the progress in the sludge-derived biochar production process and its applications in aqueous contaminant removal through adsorption and advanced oxidation processes (AOPs). The production methods and the key factors are systemically reviewed. The obtained biochar can be utilized as adsorbents and catalytic material; herein, its removal mechanisms are carefully studied Sustainability 2024 , 16 , x FOR PEER REVIEW 2 of 16 fl oc structure and richness in carbon and other reactive elements. Compared to conventional sludge treatment methods, including anaerobic digestion, composting, and incineration, producing biochar using sludge has gained increasing a tt ention. As calculated and summarized in Figure 1, publications focusing on biochar and sludge-derived biochar in the past decade have been increasing drastically. Transforming sludge into functional biochar is an environmentally friendly technique, which can not only remove hazardous compounds such as pathogens and organic pollutants from sludge and reduce the volume of sludge, but can also convert the organic ma tt er in sludge into bio-oil and bio-gas, for use as fuels [2]. Meanwhile, the residual solid, which is called sludge-derived biochar, is proven to have a porous structure with a large speci fi c surface area and abundant oxygen-containing functional groups with good metal-binding a ffi nity, which can be further developed as adsorbents and catalysts [3]. This review provides a deep insight into the progress in the sludge-derived biochar production process and its applications in aqueous contaminant removal through adsorption and advanced oxidation processes (AOPs). The production methods and the key factors are systemically reviewed. The obtained biochar can be utilized as adsorbents and catalytic material; herein, its removal mechanisms are carefully studied. Figure 1. Evolution of the number of publications on biochar and sludge-based biochar between 2014 and 2023 (data from Web of Science; keywords used for search were “biochar” and “biochar and sludge”). 2. Production of Sludge-Derived Biochar The method for preparing sludge-derived biochar follows a similar routine, which mainly includes preprocessing, pyrolysis, collection, and characterization. In the preprocessing stage, the sludge will undergo drying, sieving, and activating. The drying process is often performed at 105 °C for 24 h with the purpose of reducing the volume of sludge and saving energy consumption for the subsequent pyrolysis. During the whole production process, the properties of sludge-derived biochar are a ff ected by many factors, such as sludge moisture content, sludge modi fi cation and/or activation method, pyrolysis temperature, retention time, heating rate, pyrolysis atmosphere, etc. In general, the production of sludge-derived biochar can be determined mainly by two categories: (1) the sludge’s inherent properties and (2) the production process parameters. 2.1. E ff ects of Sludge’s Inherent Properties As the sludge-derived biochar’s precursor, raw sludge will directly a ff ect the physico-chemical properties of as-obtained biochar. Compared to conventional lignocellulosic biomass, sludge usually has a relatively higher nitrogen content (around 3.8% on average) because of peptides and proteins. The content and type of elements vary in sludges obtained from di ff erent wastewater and treatment sections. For example, compared with municipal sludge, the composition of industrial sludge is more complicated and pollut- Figure 1. Evolution of the number of publications on biochar and sludge-based biochar between 2014 and 2023 (data from Web of Science; keywords used for search were “biochar” and “biochar and sludge”) 2. Production of Sludge-Derived Biochar The method for preparing sludge-derived biochar follows a similar routine, which mainly includes preprocessing, pyrolysis, collection, and characterization. In the preprocessing stage, the sludge will undergo drying, sieving, and activating. The drying process is often performed at 105 ◦ C for 24 h with the purpose of reducing the volume of sludge and saving energy consumption for the subsequent pyrolysis. During the whole production process, the properties of sludge-derived biochar are affected by many factors, such as sludge moisture content, sludge modification and/or activation method, pyrolysis temperature, retention time, heating rate, pyrolysis atmosphere, etc. In general, the production of sludge-derived biochar can be determined mainly by two categories: (1) the sludge’s inherent properties and (2) the production process parameters 2.1. Effects of Sludge’s Inherent Properties As the sludge-derived biochar’s precursor, raw sludge will directly affect the physicochemical properties of as-obtained biochar. Compared to conventional lignocellulosic biomass, sludge usually has a relatively higher nitrogen content (around 3.8% on average) because of peptides and proteins. The content and type of elements vary in sludges obtained from different wastewater and treatment sections. For example, compared with municipal sludge, the composition of industrial sludge is more complicated and polluted.

[Find the meaning and references behind the names: Element, Mol, New, Rice, Iron, Wang, Low, Active, Excellent, Fenton, Chain, Basic, Original, Ability, Dye, Valence, Mass, State, Acid, Koh, Red, Chen, Rather, Rich, Blue, Pore, Bonds, Printing, Orange, Min, Pre, Quality, Focus]

Sustainability 2024 , 16 , 5012 3 of 16 Papermaking sludge contains lots of organic matter such as lignin and cellulose, higher inorganic contents (Ca, Si), and low heavy metal contents. These biochars showed excellent performance in phosphate adsorption. Printing and dyeing sludge contains many dyeing agents, polycyclic aromatic hydrocarbons, and relatively high heavy metal contents (Cu, Ni, Cr), and the derived biochar could be utilized as catalysts for AOPs after careful treatment [ 4 ]. Basically, the sludge contains conventional elements (C, H, O, and N), bioelements (P and S), inorganic elements (Ca, Mg, Si, Fe, Al, and Cl), and toxic heavy metal elements (Cu, Ni, Pb, Cd, Zn, As, Cd. . .). Among them, carbon is the dominant element and its content is the most basic and key index for measuring the quality of biochar [ 5 ]. During the thermochemical process, the organic components undergo a serious complicated chain reaction and convert into aliphatic carbons (at 100–300 ◦ C), aromatic carbons (at 400–700 ◦ C), and graphite carbon at high temperatures [ 6 ]. The carbon in its existing form and carbon-based chemical bonds will further affect the surface functional groups and affinities of the obtained sludge-derived biochar in practical applications. Despite the low carbon content in the original sludge (around 20%), the average carbon content could be enhanced dramatically, up to 75.01%, after carbonization [ 7 ]. Different contents of organic nitrogen will convert into pyridine-N, pyrrole-N, graphitized-N, and oxidized-N through a thermochemical process. The proportions of the nitrogen species will affect the derived biochar’s adsorption ability and catalytic reaction kinetics, since it could modulate the electronic properties of the sp 2-hybridized carbon layer and, thus, new active sites may be created [ 8 ]. Moreover, the inorganic elements in sludge are closely related to the pollutant’s removal ability, while the metal elements can facilitate the graphitization process and act as the active sites for the pollutants’ catalytic reactions [ 9 ]. For example, some sludges are abundant in element iron. The obtained Fe-rich sludge-derived biochar can be utilized as a catalyst for organic pollutant removal through Fenton-like reactions Considering the composition of sludge will directly affect the characteristics of sludgederived biochar. Many research studies focus on the modification and conditioning of sludge through metal-doping, co-pyrolysis with other feedstocks, or introducing active substances. Yu et al. [ 10 ] fabricated Cu-doped sludge biochar (CSBC) for peroxydisulfate (PDS) activation to degrade Bisphenol A (100 mg/L, PDS = 0.5 g/L, catalysts = 0.7 g/L) in high-salinity wastewater. The introduced Cu species has a valence state of Cu 0 , Cu I , and Cu II , which could greatly promote catalytic kinetics. The process was found to be dominated by singlet oxygen ( 1 O 2 ). Wang et al. [ 11 ] prepared CuFe 2 O 4 -doped sludgederived biochar for Bisphenol S removal through a PDS activation process. It was found that 84.5% Bisphenol S (20 mg/L, PS = 8 × 10 − 3 mol · dm − 3 , catalysts = 0.8 g/L) could be removed within 120 min. The introduction of metal elements benefit from the PDS activation and generate reactive oxygen species, such as sulfate radical (SO 4 · − ), hydroxyl radical ( · OH), and singlet oxygen( 1 O 2 ). Chen et al. [ 12 ] mixed sewage sludge with rice husk (Mass ratio of 1:1) (SRHB) and then performed co-pyrolysis at 500 ◦ C. The obtained SRHB showed an excellent adsorption ability towards various dyes. It had a maximum sorption capacity of 59.77 mg/g (for direct red), 42.12 mg/g (for acid orange), 38.46 mg/g (for react blue), and 22.59 mg/g (for methylene blue). Furthermore, SRHB with biomass added can form an aromatic structure and strengthen the π - π stacking interaction for dye removal. Yu et al. [ 13 ] introduced nitrogen into sludge-derived biochar production. The obtained nitrogen-doped biochar showed an excellent performance on tetracycline (TC) removal using a peroxymonosulfate (PMS) activation process. Under acidic conditions, 82.2% of TC at a rather high concentration (100 mg/L) was degraded within 120 min (PMS = 1.6 × 10 − 3 mol · dm − 3 , catalysts = 0.2 g/L) · OH and SO 4 · − were the dominant active species for TC removal Nevertheless, the biochar obtained from sludge suffers from an undeveloped pore structure and a low specific area, which limits its further application. The activation of sludge as a pre-treatment is considered to be an effective method for optimizing the pore structure and functional groups. In general, the activators include sodium hydroxide (NaOH), potassium hydroxide (KOH), phosphoric acid (H 3 PO 4 ), water vapor (H 2 O), and

[Find the meaning and references behind the names: Zhang, Range, Rapid, Less, Ghz, Unique, Cao, Ash, Fast, Pine, Slow, Novel, Htc, Mpa, Gel, Milder, Table, Alkali, Ion, Bet, Heat]

Sustainability 2024 , 16 , 5012 4 of 16 zinc compounds [ 14 , 15 ]. Min et al. [ 16 ] found that zinc chloride (ZnCl 2 ) impregnation could lead to an increase in sludge-derived biochar yield and in the content of S and O elements. Increased specific functional groups were obtained and the aromaticity and hydrophilicity of the biochar were improved. In addition, ZnCl 2 also could act as chlorinating agent to passivate and reduce the total content of heavy metals in sludge through chlorination, thereby lowering the ecological risks. Li et al. [ 17 ] produced KOH-activated biochars derived from a mixture of sewage sludge and pine sawdust. The textual properties and functional groups were found to be significantly enhanced after KOH activation. Meanwhile, the specific surface area was increased by 3.9–14.5 times and the microporosity was fully developed, which contributed to an increased adsorption capacity for CO 2 capture (136.7–182.0 mg/g) Notably, some researchers found that the above activators may damage industrial equipment or cause secondary pollution. Studies on milder activators have been investigated and carried out. Zhang et al. [ 18 ] produced sludge-derived biochar from cassava ethanol sludge for the first time by using NaHCO 3 , an environmentally friendly weak alkali, as an activator. The NaHCO 3 -activated biochar showed an enhanced adsorption capacity (154.45 mg/g) for TC, compared to raw biochar (34.04 mg/g). This novel activator could not only increase the contents of C, H, N, and O, but also efficiently removed ash from the obtained biochar in the thermal activation process, which benefitted the BET surface area and resulted in an enhanced adsorption capacity. Gu et al. [ 19 ] replaced NaOH with CaO, a gas-hardening inorganic gel, as an activator for sludge-based biochar production. The obtained CaO-activated biochar showed superior adsorption capacity for Cd (II) (43 mg/g), and its mechanical strength was improved. It was observed that CaO can increase the specific surface area and calcium ion content of the sludge-based biochar, which can improve the effective sites and surface functional groups 2.2. Effects of Production Process Parameters Dewatered sludge can be transformed into biochar through various thermochemical methods including gasification, conventional thermal pyrolysis, microwave pyrolysis, and hydrothermal carbonization (HTC, which is also called wet pyrolysis) [ 20 ]. The selection of production techniques is crucial to the obtained biochar’s structure, morphology, composition, and other chemical properties. The various operating conditions and processes have unique intrinsic advantages, which are summarized in Table 1 . Table 1. Processes of biochar production from sludge and their advantages Production Method Operation Conditions Advantages Gasification >700 ◦ C, <1 min Rapid, stable, low volatile matter content Conventional pyrolysis 300–1000 ◦ C, >1 h Easy operation, rapid heat, most mature technology Microwave pyrolysis 0.3–300 GHz Flexibility, not affected by sludge moisture HTC 180–250 ◦ C, 1–4 MPa No pretreatment, low energy consumption Gasification is a thermochemical method that occurs in gaseous media such as nitrogen, carbon dioxide, or limited oxygen and air, etc., and turns the carbonaceous biomass into gaseous fuel. In comparison to other processes, the biochars obtained through gasification are more stable under thermal conditions and generate less volatile matter The conventional pyrolysis method is the most widely studied and used method. The pyrolysis parameters, such as temperature, heating rates, residue time, and atmospheric pressure, are pivotal for determining the pyrolysis process [ 21 ]. According to the temperature range, classical pyrolysis is divided into fast pyrolysis (temperature > 500 ◦ C), moderate pyrolysis (temperature 300–500 ◦ C), and slow pyrolysis (temperature < 300 ◦ C) [ 22 ]. Fast and moderate pyrolysis can facilitate the decomposition of organic materials, which enhances the

[Find the meaning and references behind the names: Step, Choice, Malhotra, Better, Mild, Polar, Liang, Vital, Great, Gentle, Cases, Break, Size, Cross, Marin, Hard, Mud, Small, Batista]

Sustainability 2024 , 16 , 5012 5 of 16 liquid and gaseous fractions, resulting in a higher yield of bio-oil. In contrast, slow pyrolysis results in a higher solid fraction owing to the longer residue times. Moreover, compared to slow pyrolysis, in the fast pyrolysis process, more carboxyl and hydroxyl groups can be formed, and the particle size of sludge-derived biochar is relatively small, which benefits the active sites’ exposure. The temperature of pyrolysis directly affects the carbon content and the properties of sludge-derived biochar. Generally, a low temperature favors the biochar yield, while a higher temperature results in better catalytic and adsorption performances [ 23 ] In the low-temperature pyrolysis process, the cross-linkage in carbon atoms is hard to break due to the low energy inputs; thus, the macrostructure in raw sludge remains. Polar functional groups, such as -COOH, -C=O, and -CO-, are more easily obtained in sludge-derived biochar with a low-temperature pyrolysis process [ 24 ]. With the increase in temperature, the C, H, N, and S contents decrease while the heavy metal contents increase. Meanwhile, the specific surface area of the obtained biochar increases with the elevating temperature, but the particle sizes are greatly reduced. Pore size distribution changes also ensued. At high temperatures, the obtained biochar tends to become more porous and more prone to metal adsorption. Liang et al. [ 25 ] produced biochar via the pyrolysis of a sewage sludge and red mud mixture for catalytic reactions. They found that, when the pyrolysis temperature increased from 500 ◦ C to 700 ◦ C, the catalytic reaction kinetics of sulfamethoxazole (SMX) degradation through PMS activation increased by 1.9 times. A higher temperature resulted in an increase in the specific surface area and in the content of C=O, Fe(II), and active sites such as pyridinic N and graphite N sites, which jointly contributed to the enhanced pollutant degradation performance. The pyrolysis temperature largely determined the output and quality of the sludge-derived biochar. In addition, the pyrolysis atmosphere also affected the physico-chemical properties of sludge-derived biochar. In most cases, the pyrolysis carried out in an inert atmosphere (N 2 ) removed the specific elements, modified the products’ properties, and mitigated the emission of polluting gases. NH 3 , CO 2 , and Ar were also used as flux gases for biochar synthesis [ 26 ]. Hydrothermal carbonization (HTC), which is also called wet pyrolysis, is a relatively gentle thermal transformation process. It can convert the wet raw sludge into carbonaceous biochar without dewatering and avoids costly drying steps, considering its adaptability for high moisture. Compared to conventional pyrolysis, the energy consumption for the HTC process is significantly lower. Since HTC operates below 250 ◦ C, the biochar or so-called hydrochar obtained can rarely attain high levels of carbonization and has a lower carbon content [ 27 ]. However, a higher oxygen content exists, as oxygenated function groups can be found in sludge-derived biochar obtained through the HTC process. HTC has been proven to be a suitable and effective method for producing sludge-derived biochar and for further applications. Marin-Batista et al. [ 28 ] used anaerobically digested sewage sludge as a raw material for phosphorus recovery through HTC at 180–240 ◦ C. The reaction temperature affected the organic P and inorganic P retention yields. A mild temperature of 180–210 ◦ C is recommended for HTC. Malhotra et al. [ 29 ] obtained biochar through HTC, based on the mixed centrifuged sewage sludge for energy recovery and the extraction of value-added compounds. HTC was performed under high pressure at 200 ◦ C for 1–8 h. It was found that the oxygen content was significantly reduced and the fuel properties were improved when treated for 3 h or longer. The reaction duration in the HTC process is of great importance to the products’ properties. Apart from producing biochar, HTC can also be an excellent method for improving the sludge dewaterability and reducing the volume of high-moisture sludge Overall, the choice of methods and treatment parameters are vital for the production of sludge-derived biochar. Optimizing the production process is the first step for utilizing the useful substances in sludge and obtaining high-quality sludge-derived biochar.

[Find the meaning and references behind the names: Tank, Long, Areas, Simple, Green, Black]

Sustainability 2024 , 16 , 5012 6 of 16 3. Application of Sludge-Derived Biochar in Wastewater Treatment 3.1. Adsorption Compared to conventional wastewater treatment technologies, such as membrane separation, ion exchange, coagulation, and chemical precipitation, the adsorption process is simple and feasible [ 30 ]. Biochar has long been regarded as an excellent adsorbent material due to its large specific area and abundant oxygen-containing functional groups [ 31 ]. The sludge-derived biochar, which has a good carbon matrix, is proven to have a good adsorption ability for heavy metals, dyes, pharmaceuticals, ammonia nitrogen, phosphorus, emerging contaminants, oils, and other organic pollutants. In this process, the adsorption capacity is the pivotal index for assessing the adsorption performance. Usually, the characteristics of raw sludge and the pyrolysis conditions will jointly affect the adsorption capacity, by bringing in different element contents, porosities, pore size distributions, available surface areas, and surface functional groups. Table 2 presents the different experimental conditions, the characteristics of sludge-derived biochar, and their adsorption performance for different contaminants Table 2. Preparation of sludge-derived biochar and its adsorption performance Material Conditions Type Contaminants Specific Surface Area Adsorption Capacity Ref. Sewage sludge modified by hydroxyapatite Pyrolysis temperature: 550 ◦ C, 2 h, pH 4–8 Heavy metal Cu(II); Cd(II) / 89.98 mg/g; 114.68 mg/g [ 32 ] Sewage sludge/MnFe 2 O 4 loaded Hydrothermal temperature: 180 ◦ C, 10 h, pH 5–6 Heavy metal Pb(II) 129.29 m 2 /g 174.22 mg/g [ 33 ] Sewage sludge Pyrolysis temperature: 600 ◦ C, 2 h, pH 1–2 Heavy metal Cr(VI) 487.59 m 2 /g 150.84 mg/g [ 34 ] Sewage sludge activated by ZnCl 2 Pyrolysis temperature: 750 ◦ C, 2 h, pH 5–6 Dyes Methylene blue 461.44 m 2 /g 24.83 mg/g [ 35 ] Tannery sludge activated by melamine and KOH Pyrolysis temperature: 550 ◦ C, 3 h Dyes Active red X-3 B; direct yellow RS; cationic blue X-GRL; acid blue 2 GL 47.67 m 2 /g 45.13 mg/g; 84.10 mg/g; 154.80 mg/g; 120.92 mg/g [ 36 ] Industrial sludge activated by ZnCl 2 Pyrolysis temperature: 800 ◦ C, 1 h, pH 5–6 Dyes Reactive black 5; green alizarin 702.4 m 2 /g 256.02 mg/g; 312.69 mg/g [ 37 ] Dyeing sludge activated by KOH Pyrolysis temperature: 800 ◦ C, 3 h, pH 5 Antibiotics Tetracycline 1178.4 m 2 /g 1081.3 mg/g [ 38 ] Pharmaceutical sludge activated by NaOH Pyrolysis temperature: 600 ◦ C, pH 3–8 Antibiotics Tetracycline / 379.8 mg/g [ 39 ] Beverage sludge Pyrolysis temperature: 800 ◦ C Pharmaceuticals Paracetamol; ibuprofen; ketoprofen 642.00 m 2 /g 145 mg/g (pH 8); 105 mg/g (pH 4); 57 mg/g (pH 6) [ 40 ] Septic tank sludge activated by KOH Pyrolysis temperature: 800 ◦ C Inorganic substance Phosphate 82.90 m 2 /g 42.51 mg/g [ 41 ]

[Find the meaning and references behind the names: Double, Bta, Cont, Single, Present, Austria, Main, Dry, Wheat, Bond, Still, Target]

Sustainability 2024 , 16 , 5012 7 of 16 Table 2. Cont Material Conditions Type Contaminants Specific Surface Area Adsorption Capacity Ref. Dewatered dry sludge Pyrolysis temperature: 700 ◦ C, 1 h, pH 11 Inorganic substance Phosphate 20.93 m 2 /g 51.79 mg/g [ 42 ] Oil sludge activated by ZnCl 2 Pyrolysis temperature: 800 ◦ C, 1 h, pH 9 Oil Gasoil 110.00 m 2 /g 406.8 mg/g [ 43 ] Paper sludge/wheat husks, Austria Pyrolysis temperature: 500 ◦ C, 20 min, pH 2.8 Pesticides 2,4-DCP 63.80 m 2 /g 17.51 mg/g [ 44 ] Activated sludge pretreated by FeCl 3 · 6 H 2 O Pyrolysis temperature: 600 ◦ C 2 h, pH 3 Pesticides Tebuconazole; linuron 79.24 m 2 /g 12.37 mg/g; 9.06 mg/g [ 45 ] Sewage sludge Pyrolysis temperature: 550 ◦ C, 2 h, pH 7.5 Other organic pollutants Tetrabromobisphenol A (TBBPA) / 87.02 mg/g [ 46 ] Sewage sludge/Layered double hydroxides composited Pyrolysis temperature: 550 ◦ C, 2 h, pH 3–4 Other organic pollutants Benzotriazole (BTA) 111.74 m 2 /g 239.6 mg/g [ 47 ] It can be inferred that sludge-derived biochar has a good adsorption performance for all kinds of pollutants from the table. Notably, pollutants often coexist in contaminated wastewater systems, where competitive sorption always occurs. The decrease or the increase in adsorption performance is determined by the nature of the biochar and the pollutants. Despite the competitive adsorption between target pollutants, the sludge-derived biochar shows excellent adsorption behavior in complicated conditions. Ni et al. [ 48 ] obtained biochar derived from anaerobically digested sludge and studied its adsorption ability for Pb(II) and Cd(II). The mechanisms of the adsorption were investigated via single-metal and binarymetal systems. In the single-metal system, a higher adsorption capacity was found for Pb(II) (0.75 × 10 − 3 mol · dm − 3 · g − 1 ) compared to Cd(II) (0.55 × 10 − 3 mol · dm − 3 · g − 1 ). Meanwhile, in the binary-metal systems, the Cd (II) adsorption was inhibited to some extent, due to the competing adsorption sites, while Pb(II) had a greater affinity for obtained biochar. The obtained sludge-derived biochar still worked when heavy metal ions coexisted in the untreated water. According to the different pollutants treated, there were different adsorption mechanisms or multiple adsorption mechanisms involved. At present, electrostatic attractions, π - π bond interactions, and H-bonding are the three main adsorption mechanisms widely studied, especially for organic pollutant removal [ 20 ]. For heavy metal ion adsorption, the mechanism is more complicated, considering the heterogeneity and chemical properties of the biochar surface, the ionic environment of the aqueous solution, and the surface charge of the pollutants [ 49 , 50 ]. The adsorption between heavy metals and sludge-derived biochar may be driven by hydrophobic processes, ion exchange, pore-filling, precipitation, and functional group complexation [ 51 ] (Figure 2 a). For inorganic pollutants such as phosphates, diffusion, ligand exchange, ion exchange, and electrostatic attraction jointly contribute to the adsorption process. The pharmaceuticals adsorption process involved pore-filling, electrostatic attraction, π - π stacking, and H-bonding and complexation (Figure 2 c). The adsorption mechanisms involved in typical organic pollutant adsorption are summarized in Figure 2 d.

[Find the meaning and references behind the names: Ring, Rule, Dox, Wei, Point, Ray, Place]

Sustainability 2024 , 16 , 5012 8 of 16 Sustainability 2024 , 16 , x FOR PEER REVIEW 8 of 16 functional group complexation [51] (Figure 2 a). For inorganic pollutants such as phosphates, di ff usion, ligand exchange, ion exchange, and electrostatic a tt raction jointly contribute to the adsorption process. The pharmaceuticals adsorption process involved porefi lling, electrostatic a tt raction, π - π stacking, and H-bonding and complexation (Figure 2 c). The adsorption mechanisms involved in typical organic pollutant adsorption are summarized in Figure 2 d. Figure 2. Mechanisms involved in the adsorption of ( a ) heavy metals, ( b ) phosphates, ( c ) pharmaceuticals, and ( d ) organic contaminates into sludge-derived biochar [52–55]. Electrostatic a tt raction occurs when two atoms or molecules are charged oppositely. The strength of these electrostatic forces is determined by the amount of surface charge and is closely related to the solution’s pH and ionic strength, as well as the pH point of zero charge (pH pzc ) of the sorbent [22,56]. As a rule, the electrostatic a tt raction is relatively weak and it is the main mechanism for ionizable organic contaminant adsorption. Elkhli fi et al. [57] obtained sludge-derived biochar for phosphate adsorption and found that the value of pH and pHpzc would directly a ff ect the adsorption performance. The uptake of phosphate is more pronounced when the pH is below the pH pzc , while the adsorption kinetics become slower when it exceeds pH pzc . Therefore, electrostatic a tt raction occurs at a speci fi c pH and strongly depends on the zero-point charge of the biochar and the solution pH. π - π interaction is a nonbonded interaction with plane structure and exists when the pollutants have aromatic rings or functional groups, as the pollutants contain C=C functional groups or benzene rings [58]. However, the spatial structure of the organic pollutants may be a ff ected by environmental pH, coexisting anions, temperature, etc. As a result, the π - π interaction and the removal e ffi ciency will change. Li et al. [46] produced sludge-derived biochar for tetrabromobisphenol A (TBBPA) adsorption. Based on the Fourier transform infrared spectrometer (FTIR) and X-ray photoelectron spectroscopy (XPS) analysis, the C=C functional group was abundant on the surface of the obtained biochar [59]. After TBBPA adsorption, the stretching vibration absorption peak of C=C functional group was signi fi cantly changed, indicating that the absorption process took place through π - π interaction. The TBBPA benzene ring structure provided π electrons, and the obtained biochar provided adsorption sites for target pollutants. Figure 2. Mechanisms involved in the adsorption of ( a ) heavy metals, ( b ) phosphates, ( c ) pharmaceuticals, and ( d ) organic contaminates into sludge-derived biochar [ 52 – 55 ]. Electrostatic attraction occurs when two atoms or molecules are charged oppositely. The strength of these electrostatic forces is determined by the amount of surface charge and is closely related to the solution’s pH and ionic strength, as well as the pH point of zero charge (pH pzc ) of the sorbent [ 22 , 56 ]. As a rule, the electrostatic attraction is relatively weak and it is the main mechanism for ionizable organic contaminant adsorption. Elkhlifi et al. [ 57 ] obtained sludge-derived biochar for phosphate adsorption and found that the value of pH and pHpzc would directly affect the adsorption performance. The uptake of phosphate is more pronounced when the pH is below the pH pzc , while the adsorption kinetics become slower when it exceeds pH pzc . Therefore, electrostatic attraction occurs at a specific pH and strongly depends on the zero-point charge of the biochar and the solution pH π - π interaction is a nonbonded interaction with plane structure and exists when the pollutants have aromatic rings or functional groups, as the pollutants contain C=C functional groups or benzene rings [ 58 ]. However, the spatial structure of the organic pollutants may be affected by environmental pH, coexisting anions, temperature, etc. As a result, the π - π interaction and the removal efficiency will change. Li et al. [ 46 ] produced sludge-derived biochar for tetrabromobisphenol A (TBBPA) adsorption. Based on the Fourier transform infrared spectrometer (FTIR) and X-ray photoelectron spectroscopy (XPS) analysis, the C=C functional group was abundant on the surface of the obtained biochar [ 59 ]. After TBBPA adsorption, the stretching vibration absorption peak of C=C functional group was significantly changed, indicating that the absorption process took place through π - π interaction. The TBBPA benzene ring structure provided π electrons, and the obtained biochar provided adsorption sites for target pollutants The hydrogen bonding mechanism refers to forming an intermolecular hydrogen bond between the oxygen-containing functional group on the biochar surface and the functional group on the organic substance [ 60 , 61 ]. Hydrogen bonding commonly exists in the adsorption process and always occurs with the π - π interaction mechanism Wei et al. [ 62 ] produced iron-loaded sludge-derived biochar for TC and doxycycline (DOX) co-adsorption. A hydrogen bond forms between the oxygenated carbon group on obtained biochar and the phenolic group of TC, which is responsible for its excellent adsorption performance. Besides environmental factors such as pH and temperature, humic acid

[Find the meaning and references behind the names: Real, Cip, Force, Quite, Life, Paa, Enough, Attack, Valent, Luo, Play, Zvi, Free, Non]

Sustainability 2024 , 16 , 5012 9 of 16 (HA) in real-life aqueous environments also influences the strength of hydrogen bonding interactions, since HA consists of various functional groups, including phenolic, carboxyl, and aromatic groups [ 63 ]. Luo et al. [ 64 ] found that low concentrations of HA could promote ciprofloxacin (CIP) removal, while a higher concentration would hinder the removal efficiency. An appropriate amount of HA is considered to be enough to facilitate the formation of oxygen-containing functional groups on the biochar surface and strengthen the hydrogen bonding force for adsorption. However, excessive HA may encapsulate the surface of sludge-derived biochar and occupy adsorption active sites Apart from the three main adsorption mechanisms discussed in detail, other mechanism cannot be neglected. The adsorption mechanisms for various kinds of contaminants may be obviously different in all aspects [ 65 ], but identifying adsorption mechanisms is indispensable. This is not only for a better understanding of the interactions between the adsorbent and the adsorbate interface; more importantly, it can facilitate the desorption process optimization [ 66 ] and benefit the obtained biochar regeneration 3.2. Advanced Oxidation Processes (AOPs) AOP technology, which has the advantages of selective oxidation and limited harmful by-products, is a type of important wastewater purification technology. It is especially efficient for organic pollutants, which are hard to biodegrade. According to the type of catalytic reaction, AOPs generally include PMS-, PDS-, hydrogen peroxide (H 2 O 2 )-, and peracetic acid (PAA)-activated oxidation processes (Figure 3 ). The mechanism of AOPs in sludge-derived biochar are more complicated because the catalytic sites are quite different from regular carbon material, considering the complex composition of sewage sludge as a precursor. During the AOPs, pollutants are degraded via radical and/or nonradical pathways. In the radical pathway, the highly reactive oxygen species · OH, SO 4 · − , and 1 O 2 are produced and oxidize the pollutants into CO 2 and H 2 O, eventually. In the non-free radical pathway, 1 O 2 and the mediated electron transfer between pollutants and catalysts play a main role in pollutant degradation. Some AOPs based on different activation processes are summarized in Table 3 . Table 3. Different AOPs process for aqueous pollutant removal Material Agents Contaminants Experimental Conditions Removal Kinetics/Efficiency Ref. Fe-rich sludge-derived biochar H 2 O 2 4-chlorophenol Pollutants 0.78 mM/L, catalysts 2 g/L, pH 2, H 2 O 2 30 mM 0.51 min − 1 [ 67 ] Municipal sewage sludge H 2 O 2 Ofloxacin Pollutants 30 mg/L, catalysts 0.1 g/L, pH 6, H 2 O 2 4 mM 91.5 ± 1.4%, [ 10 ] Zero-valent iron (ZVI) sludge PS Acid orange Pollutants 0.06 mM, catalysts 0.5 g/L, pH 5.22, PS 0.925 mM 0.0718 min − 1 [ 68 ] Red mud–sewage sludge PMS Sulfamethoxazole Pollutants 0.02 mM, catalysts 1.5 g/L, PMS 0.15 mM 0.0481 min − 1 [ 69 ] Secondary sewage sludge PDS Sulfamethoxazole Pollutants 0.04 mM, catalysts 2.0 g/L, pH 5, PDS 1.5 mM 0.0145 min − 1 [ 70 ] Mixture of primary and secondary sludge PAA 4-chlorophenol Pollutants 5 mg/L, catalysts 0.3 g/L, pH 7, PAA 1.8 mM 0.051 min − 1 [ 71 ] 3.2.1. AOPs Based on H 2 O 2 During the H 2 O 2 activation process, the strong oxidizing species · OH are generated and effectively attack contaminants. Since iron is present in sludge, sludge-derived biochar has been regarded as a Fenton-like catalyst or is modulated, via various methods for adding iron groups, to catalyze the production of · OH from H 2 O 2 . The iron content, as well as the surface functional structure, of sludge-derived biochar jointly affect the activation efficiency of H 2 O 2 , and directly determine the pollutant degradation performance.

[Find the meaning and references behind the names: Gan, Qian, Zang, Cap, Cake, Yin, Half, Spin, Boost, Seven]

Sustainability 2024 , 16 , 5012 10 of 16 Gan et al. [ 67 ] pyrolyzed a sludge cake conditioned using Fenton’s reagent and red mud and obtained Fe-rich biochar with multivalent iron compounds for 4-chlorophenol (4-CP) removal. Under different pyrolysis temperatures, the valence of Fe is varied and its catalytic ability for the H 2 O 2 activation and 4-CP degradation pathways are completely different. Apart from affecting the H 2 O 2 activation reactive sites, the iron in the sludgederived biochar can also act as an electronic mediator in the H 2 O 2 activation process. Wu et al. [ 71 ] prepared iron-rich sludge-derived hydrochar and used it for triclosan oxidation through Fenton-like reactions. Both persistent free radicals (PFRs; 19.7%) and iron (80.3%) were found to activate H 2 O 2 and to benefit pollutant oxidation. Additionally, other modified methods, including metal and non-metal-co-doped, heteroatom-doped, and acid/alkaline-modified sludge-derived biochar, as well as the biochar’s internal structural changes, could also affect the H 2 O 2 activation process 3.2.2. AOPs Based on Persulfate Persulfate-based advanced oxidation processes (PS-AOPs), represented by PMS and PDS activation, have gained a boost in attention for wastewater treatment [ 61 ]. In the PS-AOPs, SO 4 · − is the primary reactive oxygen species. Compared to · OH (2.7 V, <1 µ s), SO 4 · − has a higher redox potential (2.5–3.1 V) for organic mineralization, a longer half-life (30–40 µ s), and a wider pH tolerance [ 72 ]. PMS and PDS are two representative agents and can be activated and decomposed into reactive species (SO 4 · − , · OH, 1 O 2 , and O 2 · − ) through various types of activation, including ultraviolet (UV) irradiation, microwave activation, transition metal ion activation, etc. To be more specific, PDS has the advantages of cheaper and easier transportation, higher water solubility, and higher stability than PMS, and, thus, has broader applications in wastewater and soil remediation [ 70 ]. The generated reactive species, as well as the nonradical pathways, can effectively break down the chemical bonds in organic pollutants for wastewater purification. Notably, the degradation of organic pollutants (antibiotics, dyes, phenolic compounds, pharmaceuticals, etc.) through the PS system is more easily facilitated than in the H 2 O 2 system In addition to the above radical-based AOPs, non-free radical pathways participate in the oxidation process. At present, the number of studies on non-free radical pathways are increasing, and some researchers have found that non-free radical pathways play an even more important role 1 O 2 is the first excited electronic state of molecular oxygen and is highly reactive. It can be generated through the oxygen vacancies on sludge-derived biochar in the PMS activation process [ 69 ]. In addition, carbonyl groups and metals can also be active sites for 1 O 2 generation [ 73 ]. Yin et al. [ 70 ] pyrolyzed sewage sludge at 700 ◦ C to produce sludge-derived biochar for sulfamethoxazole (SMX) removal through PDS activation. In contrast to the traditional radical oxidation pathways in the biochar/PDS system, SO 4 · − and · OH were not produced. The excellent SMX degradation performance was on account of the non-free radical processes dominated by singlet oxygen It is noted that both free radical and non-free radical processes exist, but the proportion and dominance are different. At present, the effect and mechanism of pollutant degradation in sludge-derived biochar/PS systems has been widely studied. Zang et al. [ 74 ] produced Fe-doped biochar from waste sludge for rhodamine B removal via PMS activation. Using electron spin resonance spectroscopy detection and a free radical quenching test, SO 4 · − , · OH, 1 O 2 , and O 2 · − -were proven to be generated in the process. Large quantities of freeflowing electrons in sludge-derived biochar were believed to facilitate SO 4 · − and · OH generation. Qian et al. [ 75 ] obtained sludge-derived biochar from petrochemical sludge for chloramphenicol (CAP) removal through PMS activation. The excellent CAP removal performance was the combination of adsorption with a catalytic degradation reaction. In the biochar/PMS system, free radical and non-free radical pathways simultaneously occur, and SO 4 · − , · OH, and 1 O 2 were the main reactive species contributing to CAP degradation Fang et al. [ 76 ] prepared N-modified sludge-derived biochar (N-SDBC) for fluoroquinolone antibiotics (FQs) degradation through PDS activation. Seven commonly used FQs were proven to be degraded by the N-SDBC/PDS system, as the graphite-N and Fe 0 on the

[Find the meaning and references behind the names: Aim, Huge, Minor, Running, Bene, Major, Far, Cost, Full, Match]

Sustainability 2024 , 16 , 5012 11 of 16 N-SDBC provided active sites for PDS activation. It was found that 1 O 2 was the dominant reactive species, while the SO 4 · − and · OH played minor roles. The non-free radical pathway was shown to contribute more than the free radical pathway 3.2.3. AOPs Based on PAA Peracetic acid (PAA)-based AOPs are emerging and have been identified as an alternative technology for wastewater treatment. They are especially effective for the degradation of chlorophenols and micropollutants such as naphthyl compounds and sulfa drugs [ 77 ]. Compared to PMS and H 2 O 2 , PAA has lower O-O bond energy (PAA 159 kJ/mol, PMS 317 kJ/mol, H 2 O 2 213 kJ/mol) and, therefore, is thermally more feasible for multiple reactive species generation [ 78 ]. PAA can be activated by transition metals such as Co 2+ , Fe 2+ , Mn 2+ , and CoFe 2 O 4 to generate free radicals ( · OH, CH 3 C(O)O · , and CH 3 C(O)OO · ) [ 79 , 80 ]. Wu et al. [ 71 ] obtained sludge-derived biochar through the pyrolysis of a mixture of primary sludge and secondary sludge. The optimized biochar/PAA system exhibited an outstanding catalytic performance for 4-CP under a wide range of pH conditions through dichlorination, hydroxylation, and a ring-opening pathway. Persistent free radicals (PFRs), rather than the chemical composition or the material structure, dominated PAA activation, and RO · was found to be the major reactive species. During the pyrolysis process, organic matter and inorganic metals in the two sludges synergized and resulted in more abundant electron donation groups (C=O, -OH), which promoted PFR formation, and eventually facilitates 4-CP oxidation degradation. So far, little information on the PAA-based activation of sludge-derived biochar is available, but it is expected to be further investigated and have a large application potential in the future Sustainability 2024 , 16 , x FOR PEER REVIEW 12 of 16 Figure 3. Activating mechanisms of ( a ) H 2 O 2 , ( b ) PDS, ( c ) PMS, and ( d ) PAA on sludge-derived biochar ([67,71,74,76]). In addition to its excellent contaminant removal performance through adsorption and AOPs, its recycling and regeneration ability is vital to evaluate sludge-derived biochar. Gao et al. [38] found that the obtained sludge-derived biochar could maintain an 86.35% tetracycline removal e ffi ciency after fi ve adsorption–regeneration cycles with Fenton reaction regeneration. The morphology of the biochar was not obviously damaged. Lv et al. [81] used microwaves, coupled with hydrogen peroxide, to regenerate functional sludge-derived biochar (MSBC) after Bisphenol S adsorption. They found that the regenerated MSBC remained stable after three cycles. Ma et al. [82] reused sludge-derived biochar using NaOH regeneration and found that the adsorption ability could still reach up to 98.5% after fi ve cycles. Through di ff erent regeneration methods, sludge-derived biochar has been proven to have long-term running stability and reusability, which make it more cost-e ff ective and broaden its potential applications in practical wastewater treatment. 4. Challenges and Future Recommendations Nowadays, huge amounts of sludge are produced yearly, and they remain challenging to treat appropriately. Converting waste sludge into functional biochar has been proven to be a value-added strategy, which bene fi ts sustainable waste management, as well as sustainable environmental development. In this process, several aspects should be especially noticed. Firstly, sewage sludge from di ff erent origins and industries exhibits profound di ff erences in its chemical properties, which leads to completely di ff erent characteristics of the obtained biochar. Therefore, the factors correlating with the sludge’s chemical properties need be quantitatively analyzed. This could allow us to distinguish between and make full use of the components in sludge. Secondly, to achieve speci fi c properties of the obtained biochar and to further match it to speci fi c applications, the production process should be consciously regulated. Parameters ranging from pyrolysis temperature, pyrolysis atmosphere, heating rates, and activation method to additive substances should be deliberately modulated and designed, in order to aim for a sludge-derived biochar with speci fi c functions. Furthermore, the sludge-derived biochar used for environmental remediation has some challenges and restrictions, such as economic problems and possible environmental risks. Compared to traditional sewage sludge disposal methods, pyrolyzing sewage Figure 3. Activating mechanisms of ( a ) H 2 O 2 , ( b ) PDS, ( c ) PMS, and ( d ) PAA on sludge-derived biochar ([ 67 , 71 , 74 , 76 ]). In addition to its excellent contaminant removal performance through adsorption and AOPs, its recycling and regeneration ability is vital to evaluate sludge-derived biochar Gao et al. [ 38 ] found that the obtained sludge-derived biochar could maintain an 86.35% tetracycline removal efficiency after five adsorption–regeneration cycles with Fenton

[Find the meaning and references behind the names: Turn, Price, Guide, Balance]

Sustainability 2024 , 16 , 5012 12 of 16 reaction regeneration. The morphology of the biochar was not obviously damaged. Lv et al. [ 81 ] used microwaves, coupled with hydrogen peroxide, to regenerate functional sludge-derived biochar (MSBC) after Bisphenol S adsorption. They found that the regenerated MSBC remained stable after three cycles. Ma et al. [ 82 ] reused sludge-derived biochar using NaOH regeneration and found that the adsorption ability could still reach up to 98.5% after five cycles. Through different regeneration methods, sludge-derived biochar has been proven to have long-term running stability and reusability, which make it more cost-effective and broaden its potential applications in practical wastewater treatment 4. Challenges and Future Recommendations Nowadays, huge amounts of sludge are produced yearly, and they remain challenging to treat appropriately. Converting waste sludge into functional biochar has been proven to be a value-added strategy, which benefits sustainable waste management, as well as sustainable environmental development. In this process, several aspects should be especially noticed. Firstly, sewage sludge from different origins and industries exhibits profound differences in its chemical properties, which leads to completely different characteristics of the obtained biochar. Therefore, the factors correlating with the sludge’s chemical properties need be quantitatively analyzed. This could allow us to distinguish between and make full use of the components in sludge. Secondly, to achieve specific properties of the obtained biochar and to further match it to specific applications, the production process should be consciously regulated. Parameters ranging from pyrolysis temperature, pyrolysis atmosphere, heating rates, and activation method to additive substances should be deliberately modulated and designed, in order to aim for a sludge-derived biochar with specific functions Furthermore, the sludge-derived biochar used for environmental remediation has some challenges and restrictions, such as economic problems and possible environmental risks. Compared to traditional sewage sludge disposal methods, pyrolyzing sewage sludge to create biochar inevitably requires more heat and energy consumption, resulting in higher costs. The production price of biochar is determined by the whole production process, including feedstock supply, sludge drying, pyrolysis, transportation, storage, the cost of labor, etc. For example, seeking cheaper raw materials or using industrial waste heat to dry the sludge could lower the cost, to some extent. The pyrolysis temperature and heating time can directly affect the biochar yield. Therefore, future development of sludge-derived biochar needs to seek a better balance between the quality, yield, and cost of biochar. Also, the raw sludge contains heavy metals, toxic substances, nitrogen, and phosphorus. When using sludge-derived biochar as an adsorbent or catalyst, it may cause eutrophication or secondary pollution. Therefore, in the preparation process of biochar, harmful substances and heavy metals need to be removed or immobilized by means of pretreatment. Also, the quantity of pollutants should be accurately determined based on the biochar’s characterization and degradation capacity 5. Conclusions This review summarizes the recent progress in sludge-derived biochar production processes, including the synthesis methods and the key factors affecting the quality of obtained biochar. It is concluded that the selection of the appropriate thermochemical process and the operation parameters are of great significance. The obtained biochar has potential for practical applications, especially for wastewater purification through adsorption and advanced oxidation processes. Clarifying the adsorption and catalytic reaction mechanism would be helpful in better understanding pollutant degradation and mineralization, and would also purposefully guide the production of sludge-derived biochar in turn.

[Find the meaning and references behind the names: Eng, Liu, Natural, Xiong, Dong, Kong, Xie, Yuan, Duan, Zeng, Gal, Farr, Zhao, Jiang, Risk, Niu, Jelic, Sci, Qin, Read, Chem, Xiao, Leng, Shao, Huang, Wan, Guerra, Petrovic, Sun, Pang, Situ, Yao, Alda, Cruz, Mater, Postigo, Grant, Feng, Bai, Pan, Sheng, Thank, Hou, Dang, Author, Hazard, Tang, Yan, Deng, Shi]

Sustainability 2024 , 16 , 5012 13 of 16 Author Contributions: Conceptualization, Y.Z. and J.L.; writing—original draft preparation, Y.Z and J.G.; visualization, J.G.; investigation, X.Y. and H.N.; formal analysis, J.Q. and Z.Z.; methodology, Y.Y.; validation, D.F.; supervision, L.Z and J.L.; writing—review and editing, L.Z. and J.L. All authors have read and agreed to the published version of the manuscript Funding: This research was funded by Jiangsu Agriculture Science and Technology Innovation Fund [CX(22)3135]; the National Natural Science Foundation of China [Grant No. 52200098, U 22 A 20433]; and the Science and Technology Innovation Project on Emission Peak and Carbon Neutrality of Jiangsu Province [BK 20220040] Data Availability Statement: The data used in the current study are available from the corresponding author upon request Acknowledgments: The authors thank the editors and anonymous reviewers for their valuable comments and suggestions Conflicts of Interest: The authors declare no conflicts of interest References 1 D í az-Cruz, M.; Garc í a-Gal á n, M.; Guerra, P.; Jelic, A.; Postigo, C.; Eljarrat, E.; Farr é , M.; de Alda, M.L.; Petrovic, M.; Barcel ó , D.; et al. Analysis of selected emerging contaminants in sewage sludge Trends Anal. Chem 2009 , 28 , 1263–1275. [ CrossRef ] 2 Zhao, L.; Sun, Z. Sewage sludge derived biochar for environmental improvement: Advances, challenges, and solutions Water Res. X 2023 , 18 , 100167. [ CrossRef ] 3 Ma, Y.; Wu, L.; Li, P.; Yang, L.; He, L.; Chen, S.; Yang, Y.; Gao, F.; Qi, X.; Zhang, Z. A novel, efficient and sustainable magnetic sludge biochar modified by graphene oxide for environmental concentration imidacloprid removal J. Hazard. Mater 2021 , 407 , 124777. [ CrossRef ] 4 Chen, J.; Bai, X.; Yuan, Y.; Zhang, Y.; Sun, J. Printing and dyeing sludge derived biochar for activation of peroxymonosulfate to remove aqueous organic pollutants: Activation mechanisms and environmental safety assessment Chem. Eng. J 2022 , 446 , 136942. [ CrossRef ] 5 Xu, Y.; Chen, B. Investigation of thermodynamic parameters in the pyrolysis conversion of biomass and manure to biochars using thermogravimetric analysis Bioresour. Technol 2013 , 146 , 485–493. [ CrossRef ] 6 Zhu, S.; Huang, X.; Ma, F.; Wang, L.; Duan, X.; Wang, S. Catalytic removal of aqueous contaminants on n-doped graphitic biochars: Inherent roles of adsorption and nonradical mechanisms Environ. Sci. Technol 2018 , 52 , 8649–8658. [ CrossRef ] [ PubMed ] 7 Yao, Y.; Zhao, W.; Liu, C.; Gao, J.; Yang, X.; Xiao, C.; Qi, J.; Zhou, Y.; Zhu, Z.; Yang, Y.; et al. Iron containing sludge-derived carbon towards efficient peroxymonosulfate activation: Active site synergy, performance and alternation mechanism Sci. Total Environ 2024 , 915 , 170183. [ CrossRef ] [ PubMed ] 8 Long, Y.; Bu, S.; Huang, Y.; Shao, Y.; Xiao, L.; Shi, X. N-doped hierarchically porous carbon for highly efficient metal-free catalytic activation of peroxymonosulfate in water: A non-radical mechanism Chemosphere 2019 , 216 , 545–555. [ CrossRef ] 9 Huang, B.; Jiang, J.; Huang, G.; Yu, H. Sludge biochar-based catalyst for improved pollutant degradation by activating peroxymonosulfate J. Mater. Chem. A 2018 , 6 , 8978–8985. [ CrossRef ] 10 Yu, C.; Yan, C.; Gu, J.; Zhang, Y.; Li, X.; Dang, Z.; Wang, L.; Wan, J.; Pan, J. In-situ Cu-loaded sludge biochar catalysts for oxidative degradation of bisphenol A from high-salinity wastewater J. Clean 2023 , 427 , 139334. [ CrossRef ] 11 Wang, B.; Li, Q.; Lv, Y.; Fu, H.; Liu, D.; Feng, Y.; Xie, H.; Qu, H. Insights into the mechanism of peroxydisulfate activated by magnetic spinel CuFe 2 O 4 /SBC as a heterogeneous catalyst for bisphenol S degradation Chem. Eng. J 2021 , 416 , 129162 [ CrossRef ] 12 Chen, S.; Qin, C.; Wang, T.; Chen, F.; Li, X.; Hou, H.; Zhou, M. Study on the adsorption of dyestuffs with different properties by sludge-rice husk biochar: Adsorption capacity, isotherm, kinetic, thermodynamics and mechanism J. Mol. Liq 2019 , 285 , 62–74 [ CrossRef ] 13 Yu, J.; Tang, L.; Pang, Y.; Zeng, G.; Wang, J.; Deng, Y.; Liu, Y.; Feng, H.; Chen, S.; Ren, X. Magnetic nitrogen-doped sludge-derived biochar catalysts for persulfate activation: Internal electron transfer mechanism Chem. Eng. J 2019 , 364 , 146–159. [ CrossRef ] 14 Huang, K.; Hu, C.; Tan, Q.; Yu, M.; Shabala, S.; Yang, L.; Sun, X. Highly efficient removal of cadmium from aqueous solution by ammonium polyphosphate-modified biochar Chemosphere 2022 , 305 , 135471. [ CrossRef ] [ PubMed ] 15 Leng, L.; Xiong, Q.; Yang, L.; Li, H.; Zhou, Y.; Zhang, W.; Jiang, S.; Li, H.; Huang, H. An overview on engineering the surface area and porosity of biochar Sci. Total Environ 2021 , 763 , 144204. [ CrossRef ] 16 Min, X.; Ge, T.; Li, H.; Shi, Y.; Fang, T.; Sheng, B.; Li, H.; Dong, X. Combining impregnation and co-pyrolysis to reduce the environmental risk of biochar derived from sewage sludge Chemosphere 2022 , 290 , 133371. [ CrossRef ] 17 Li, K.; Zhang, D.; Niu, X. Insights into CO 2 adsorption on KOH-activated biochars derived from the mixed sewage sludge and pine sawdust Sci. Total Environ 2022 , 826 , 154133. [ CrossRef ] 18 Zhang, Z.; Li, Y.; Ding, L.; Yu, J.; Zhou, Q.; Kong, Y.; Ma, J. Novel sodium bicarbonate activation of cassava ethanol sludge derived biochar for removing tetracycline from aqueous solution: Performance assessment and mechanism insight Bioresour. Technol 2021 , 330 , 124949. [ CrossRef ]

[Find the meaning and references behind the names: Art, Kayan, Rubia, Osman, Nie, Plant, Garg, Hog, Khan, Song, Sharma, Dotto, Akay, Wood, Bouzidi, Sarmah, Valizadeh, Han, Khiari, Salman, Zhan, Ansari, Xing, Char, Bennici, Front, Dubey, Noreen, Saf, Amari, Streit, Zheng, Sep, Lett, Sellaoui, Zhai, Tian, Guez, Alshammari, Kulaksiz, Lin, Shen, Oliveira, Verdi]

Sustainability 2024 , 16 , 5012 14 of 16 19 Gu, H.; Lin, W.; Sun, S.; Wu, C.; Yang, F.; Ye, Z.; Chen, N.; Ren, J.; Zheng, S. Calcium oxide modification of activated sludge as a low-cost adsorbent: Preparation and application in Cd(II) removal Ecotoxicol. Environ. Saf 2021 , 209 , 111760. [ CrossRef ] 20 Ji, Q.; Yuan, X.; Zhao, Y.; Jiang, L.; Wang, H. Mechanistic insights of removing pollutant in adsorption and advanced oxidation processes by sludge biochar J. Hazard. Mater 2022 , 430 , 128375. [ CrossRef ] 21 Zhang, H.; Chen, W.; Qi, Z.; Qian, W.; Yang, L.; Wei, R.; Ni, J. Biochar improved the solubility of triclocarban in aqueous environment: Insight into the role of biochar-derived dissolved organic carbon Chemosphere 2024 , 351 , 141172. [ CrossRef ] [ PubMed ] 22 Luo, Z.; Yao, B.; Yang, X.; Wang, L.; Xu, Z.; Yan, X.; Tian, L.; Zhou, H.; Zhou, Y. Novel insights into the adsorption of organic contaminants by biochar: A review Chemosphere 2022 , 287 , 132113. [ CrossRef ] 23 Khiari, B.; Jeguirim, M.; Limousy, L.; Bennici, S. Biomass derived chars for energy applications Renew. Sustain. Energy Rev 2019 , 108 , 253–273. [ CrossRef ] 24 Liang, F.; Xing, B. Black carbon (biochar) in water/soil environments: Molecular structure, sorption, stability, and potential risk Environ. Sci. Technol 2017 , 51 , 13517–13532. [ CrossRef ] [ PubMed ] 25 Liang, L.; Wang, Y.; Li, N.; Yan, B.; Chen, G.; Hou, L. Breaking rate-limiting steps in a red mud-sewage sludge carbon catalyst activated peroxymonosulfate system: Effect of pyrolysis temperature Sep. Purif. Technol 2022 , 299 , 121805. [ CrossRef ] 26 Sun, C.; Chen, T.; Huang, Q.; Zhan, M.; Li, X.; Yan, J. Activation of persulfate by CO 2 -activated biochar for improved phenolic pollutant degradation: Performance and mechanism Chem. Eng. J 2020 , 380 , 122519. [ CrossRef ] 27 Sharma, H.; Sarmah, A.; Dubey, B. Hydrothermal carbonization of renewable waste biomass for solid biofuel production: A discussion on process mechanism, the influence of process parameters, environmental performance and fuel properties of hydrochar Renew. Sustain. Energy Rev 2020 , 123 , 109761. [ CrossRef ] 28 Marin-Batista, J.; Mohedano, A.; Rodr í guez, J.; de la Rubia, M. Energy and phosphorous recovery through hydrothermal carbonization of digested sewage sludge Waste Manag 2020 , 105 , 566–574. [ CrossRef ] [ PubMed ] 29 Malhotra, M.; Garg, A. Hydrothermal carbonization of centrifuged sewage sludge: Determination of resource recovery from liquid fraction and thermal behaviour of hydrochar Waste Manag 2020 , 117 , 114–123. [ CrossRef ] 30 Charerntanyarak, L. Heavy metals removal by chemical coagulation and precipitation Water Sci. Technol 1999 , 39 , 135–138 [ CrossRef ] 31 Huang, Q.; Song, S.; Chen, Z.; Hu, B.; Chen, J.; Wang, X. Biochar-based materials and their applications in removal of organic contaminants from wastewater: State-of-the-art review Biochar 2019 , 1 , 45–73. [ CrossRef ] 32 Chen, Y.; Li, M.; Li, Y.; Liu, Y.; Chen, Y.; Li, H.; Chen, L. Hydroxyapatite modified sludge-based biochar for the adsorption of Cu 2+ and Cd 2+ : Adsorption behavior and mechanisms Bioresour. Technol 2021 , 321 , 124413. [ CrossRef ] 33 Chen, Y.; Xu, F.; Li, H.; Li, Y.; Liu, Y.; Chen, Y.; Chen, L. Simple hydrothermal synthesis of magnetic MnFe 2 O 4 -sludge biochar composites for removal of aqueous Pb 2+ J. Anal. Appl. Pyrol 2021 , 156 , 105173. [ CrossRef ] 34 Shi, R.; Liu, T.; Lu, J.; Liang, X.; Ivanets, A.; Yao, J.; Su, X. Fe/C materials prepared by one-step calcination of acidified municipal sludge and their excellent adsorption of Cr (VI) Chemosphere 2022 , 304 , 135303. [ CrossRef ] [ PubMed ] 35 Yin, Q.; Nie, Y.; Han, Y.; Wang, R.; Zhao, Z. Properties and the application of sludge-based biochar in the removal of phosphate and methylene blue from water: Effects of acid treating Langmuir 2022 , 38 , 1833–1844. [ CrossRef ] 36 Zhai, S.; Li, M.; Wang, D.; Ju, X.; Fu, S. Cyano and acylamino group modification for tannery sludge bio-char: Enhancement of adsorption universality for dye pollutants J. Environ. Chem. Eng 2021 , 9 , 104939. [ CrossRef ] 37 Sellaoui, L.; Said, S.; Bouzidi, M.; Alshammari, A.S.; Khan, Z.R.; Gandouzi, M.; Erto, A. Highlighting the adsorption mechanism of dyes onto activated carbon derived from sludge by theoretical physical analysis Environ. Sci. Pollut. Res 2023 , 30 , 15789–15796 [ CrossRef ] 38 Gao, J.; Zhou, Y.; Yang, X.; Yao, Y.; Qi, J.; Zhu, Z.; Yang, Y.; Fang, D.; Zhou, L.; Li, J. Dyeing sludge-derived biochar for efficient removal of antibiotic from water Sci. Total. Environ 2024 , 912 , 169035. [ CrossRef ] [ PubMed ] 39 Liu, H.; Xu, G.; Li, G. Preparation of porous biochar based on pharmaceutical sludge activated by NaOH and its application in the adsorption of tetracycline J. Colloid Interface Sci 2021 , 587 , 271–278. [ CrossRef ] 40 Streit, A.; Collazzo, G.; Druzian, S.; Verdi, R.; Foletto, E.; Oliveira, L.; Dotto, G. Adsorption of ibuprofen, ketoprofen, and paracetamol onto activated carbon prepared from effluent treatment plant sludge of the beverage industry Chemosphere 2021 , 262 , 128322. [ CrossRef ] 41 Liu, Z.; Liu, H.; Zhang, Y.; Lichtfouse, E. Efficient phosphate recycling by adsorption on alkaline sludge biochar Environ. Chem Lett 2023 , 21 , 21–30. [ CrossRef ] 42 Liu, M.; Li, R.; Wang, J.; Liu, X.; Li, S.; Shen, W. Recovery of phosphate from aqueous solution by dewatered dry sludge biochar and its feasibility in fertilizer use Sci. Total. Environ 2022 , 814 , 152752. [ CrossRef ] [ PubMed ] 43 Amari, A.; Noreen, A.; Osman, H.; Sammen, S.S.; Al-Ansari, N.; Salman, H.M. Investigation of the viable role of oil sludge-derived activated carbon for oily wastewater remediation Front. Environ. Sci 2023 , 11 , 240. [ CrossRef ] 44 Kalderis, D.; Kayan, B.; Akay, S.; Kulaksiz, E.; Gozmen, B. Adsorption of 2,4-dichlorophenol on paper sludge/wheat husk biochar: Process optimization and comparison with biochars prepared from wood chips, sewage sludge and hog fuel/demolition waste J. Environ. Chem. Eng 2017 , 5 , 2222–2231. [ CrossRef ] 45 Yang, J.; Sun, H.; Liu, Y.; Wang, X.; Valizadeh, K. The sorption of Tebuconazole and Linuron from an aqueous environment with a modified sludge-based biochar: Effect, mechanisms, and its persistent free radicals study J. Chem 2021 , 2021 , 2912054. [ CrossRef ]

[Find the meaning and references behind the names: Dos Santos, Flash, Zou, Lee, Santos, Lopez, Feo, Rosendahl, Bian, Usman, Rajapaksha, Adv, Bed, Hamdi, Mercury, Bilbao, Shahib, Lins, Corn, Leaf, Sepulveda, Dai, Gong, Rep, Alvarez, Cai, Meili, Lahori, Tao, Cui, Chang, Guo, Peng, Jawad, Jellali, Straw, Lei, Qiu, Cheng, Liao]

Sustainability 2024 , 16 , 5012 15 of 16 46 Li, T.; He, Y.; Peng, X. Efficient removal of tetrabromobisphenol A (TBBPA) using sewage sludge-derived biochar: Adsorptive effect and mechanism Chemosphere 2020 , 251 , 126370. [ CrossRef ] 47 Cheng, X.; Deng, J.; Li, X.; Wei, X.; Shao, Y.; Zhao, Y. Layered double hydroxides loaded sludge biochar composite for adsorptive removal of benzotriazole and Pb (II) from aqueous solution Chemosphere 2022 , 287 , 131966. [ CrossRef ] [ PubMed ] 48 Ni, B.; Huang, Q.; Wang, C.; Ni, T.; Sun, J.; Wei, W. Competitive adsorption of heavy metals in aqueous solution onto biochar derived from anaerobically digested sludge Chemosphere 2019 , 219 , 351–357. [ CrossRef ] [ PubMed ] 49 Rangabhashiyam, S.; dos Santos Lins, P.V.; de Magalh ã es Oliveira, L.M.; Sepulveda, P.; Ighalo, J.O.; Rajapaksha, A.U.; Meili, L Sewage sludge-derived biochar for the adsorptive removal of wastewater pollutants: A critical review Environ. Pollut 2022 , 293 , 118581. [ CrossRef ] 50 Chen, T.; Zhang, Y.; Wang, H.; Lu, W.; Zhou, Z.; Zhang, Y.; Ren, L. Influence of pyrolysis temperature on characteristics and heavy metal adsorptive performance of biochar derived from municipal sewage sludge Bioresour. Technol 2014 , 164 , 47–54. [ CrossRef ] 51 Cheng, N.; Wang, B.; Wu, P.; Lee, X.; Xing, Y.; Chen, M.; Gao, B. Adsorption of emerging contaminants from water and wastewater by modified biochar: A review Environ. Pollut 2021 , 273 , 116448. [ CrossRef ] [ PubMed ] 52 Jellali, S.; Khiari, B.; Usman, M.; Hamdi, H.; Charabi, Y.; Jeguirim, M. Sludge-derived biochars: A review on the influence of synthesis conditions on pollutants removal efficiency from wastewaters Renew. Sustain. Energy Rev 2021 , 144 , 111068. [ CrossRef ] 53 Ma, J.; Zhou, B.; Zhang, H.; Zhang, W. Fe/S modified sludge-based biochar for tetracycline removal from water Powder Technol 2020 , 364 , 889–900. [ CrossRef ] 54 Gao, L.; Deng, J.; Huang, G.; Li, K.; Cai, K.; Liu, Y.; Huang, F. Relative distribution of Cd 2+ adsorption mechanisms on biochars derived from rice straw and sewage sludge Bioresour. Technol 2019 , 272 , 114–122. [ CrossRef ] [ PubMed ] 55 Yang, Q.; Wang, X.; Luo, W.; Sun, J.; Xu, Q.; Chen, F.; Zhao, J.; Wang, S.; Yao, F.; Wang, D.; et al. Effectiveness and mechanisms of phosphate adsorption on iron-modified biochars derived from waste activated sludge Bioresour. Technol 2018 , 247 , 537–544 [ CrossRef ] [ PubMed ] 56 Dai, Y.; Zhang, N.; Xing, C.; Cui, Q.; Sun, Q. The adsorption, regeneration and engineering applications of biochar for removal organic pollutants: A review Chemosphere 2019 , 223 , 12–27. [ CrossRef ] [ PubMed ] 57 Elkhlifi, Z.; Sellaoui, L.; Zhao, M.; Ifthikar, J.; Jawad, A.; Shahib, I.I.; Sijilmassi, B.; Lahori, A.H.; Selvasembian, R.; Meili, L.; et al. Lanthanum hydroxide engineered sewage sludge biochar for efficient phosphate elimination: Mechanism interpretation using physical modelling Sci. Total Environ 2022 , 803 , 149888. [ CrossRef ] [ PubMed ] 58 Wu, T.; Cai, X.; Tan, S.; Li, H.; Liu, J.; Yang, W. Adsorption characteristics of acrylonitrile, p-toluenesulfonic acid, 1- naphthalenesulfonic acid and methyl blue on graphene in aqueous solutions Chem. Eng. J 2011 , 173 , 144–149. [ CrossRef ] 59 Tang, J.; Lv, H.; Gong, Y.; Huang, Y. Preparation and characterization of a novel graphene/biochar composite for aqueous phenanthrene and mercury removal Bioresour. Technol 2015 , 196 , 355–363. [ CrossRef ] 60 Guo, S.; Zou, Z.; Chen, Y.; Long, X.; Liu, M.; Li, X.; Tan, J.; Chen, R. Synergistic effect of hydrogen bonding and π - π interaction for enhanced adsorption of rhodamine B from water using corn straw biochar Environ. Pollut 2023 , 320 , 121060. [ CrossRef ] 61 Yin, Z.; Liu, N.; Bian, S.; Li, J.; Xu, S.; Zhang, Y. Enhancing the adsorption capability of areca leaf biochar for methylene blue by K 2 FeO 4 -catalyzed oxidative pyrolysis at low temperature RSC Adv 2019 , 9 , 42343–42350. [ CrossRef ] [ PubMed ] 62 Wei, J.; Liu, Y.; Li, J.; Zhu, Y.; Yu, H.; Peng, Y. Adsorption and co-adsorption of tetracycline and doxycycline by one-step synthesized iron loaded sludge biochar Chemosphere 2019 , 236 , 124252. [ CrossRef ] [ PubMed ] 63 Li, M.; Wang, P.; Huang, C.; Liu, Y.; Liu, S.; Zhang, K.; Cao, J.; Tan, X.; Liu, S. Effect of dissolved humic acids and coated humic acids on tetracycline adsorption by K 2 CO 3 -activated magnetic biochar Sci. Rep 2022 , 12 , 18966. [ CrossRef ] [ PubMed ] 64 Luo, K.; Pang, Y.; Yang, Q.; Wang, D.; Li, X.; Wang, L.; Lei, M.; Liu, J. Enhanced ciprofloxacin removal by sludge-derived biochar: Effect of humic acid Chemosphere 2019 , 231 , 495–501. [ CrossRef ] 65 Shen, J.; Huang, G.; An, C.; Zhao, S.; Rosendahl, S. Immobilization of tetrabromobisphenol A by pinecone-derived biochars at solid-liquid interface: Synchrotron-assisted analysis and role of inorganic fertilizer ions Chem. Eng. J 2017 , 321 , 346–357 [ CrossRef ] 66 Alvarez, J.; Amutio, M.; Lopez, G.; Barbarias, I.; Bilbao, J.; Olazar, M. Sewage sludge valorization by flash pyrolysis in a conical spouted bed reactor Chem. Eng. J 2015 , 273 , 173–183. [ CrossRef ] 67 Gan, Q.; Hou, H.; Liang, S.; Qiu, J.; Tao, S.; Yang, L.; Yu, W.; Xiao, K.; Liu, B.; Hu, J.; et al. Sludge-derived biochar with multivalent iron as an efficient Fenton catalyst for degradation of 4-Chlorophenol Sci. Total. Environ 2020 , 725 , 138299. [ CrossRef ] [ PubMed ] 68 Wang, J.; Shen, M.; Gong, Q.; Wang, X.; Cai, J.; Wang, S.; Chen, Z. One-step preparation of ZVI-sludge derived biochar without external source of iron and its application on persulfate activation Sci. Total Environ 2020 , 714 , 136728. [ CrossRef ] [ PubMed ] 69 Wang, J.; Shen, M.; Wang, H.; Du, Y.; Zhou, X.; Liao, Z.; Wang, H.; Chen, Z. Red mud modified sludge biochar for the activation of peroxymonosulfate: Singlet oxygen dominated mechanism and toxicity prediction Sci. Total Environ 2020 , 740 , 140388 [ CrossRef ] 70 Yin, R.; Guo, W.; Wang, H.; Du, J.; Wu, Q.; Chang, J.S.; Ren, N. Singlet oxygen-dominated peroxydisulfate activation by sludgederived biochar for sulfamethoxazole degradation through a nonradical oxidation pathway: Performance and mechanism Chem. Eng. J 2019 , 357 , 589–599. [ CrossRef ] 71 Wu, L.; Li, Z.; Cheng, P.; She, Y.; Wang, W.; Tian, Y.; Ma, J.; Sun, Z. Efficient activation of peracetic acid by mixed sludge derived biochar: Critical role of persistent free radicals Water Res 2022 , 223 , 119013. [ CrossRef ] [ PubMed ]

[Find the meaning and references behind the names: Yong, Ball, Waters, Assiri, Awasthi, Masek, Dual, Selvaraj, Dobson, Lai, Catal, Mian, Uva, Ideas, Kim, Dark, Alpha, Fes, Property, Xue]

Sustainability 2024 , 16 , 5012 16 of 16 72 Zhang, J.; Song, H.; Liu, Y.; Wang, L.; Li, D.; Liu, C.; Gong, M.; Zhang, Z.; Yang, T.; Ma, J. Remarkable enhancement of a photochemical Fenton-like system (UVA/Fe(II)/PMS) at near-neutral pH and low Fe(II)/peroxymonosulfate ratio by three alpha hydroxy acids: Mechanisms and influencing factors Sep. Purif. Technol 2019 , 224 , 142–151. [ CrossRef ] 73 Mian, M.; Liu, G.; Fu, B.; Song, Y. Facile synthesis of sludge-derived MnOx-N-biochar as an efficient catalyst for peroxymonosulfate activation Appl. Catal. B Environ 2019 , 255 , 117765. [ CrossRef ] 74 Zang, T.; Wang, H.; Liu, Y.; Zhou, S.; Ai, S. Fe-doped biochar derived from waste sludge for degradation of rhodamine B via enhancing activation of peroxymonosulfate Chemosphere 2020 , 261 , 127616. [ CrossRef ] [ PubMed ] 75 Qian, L.; Yan, S.; Yong, X.; Selvaraj, M.; Ghramh, H.A.; Assiri, M.A.; Zhang, X.; Awasthi, M.K.; Zhou, J. Effective degradation of chloramphenicol in wastewater by activated peroxymonosulfate with Fe-rich porous biochar derived from petrochemical sludge Chemosphere 2023 , 310 , 136839. [ CrossRef ] [ PubMed ] 76 Fang, Z.; Zhao, S.; Xue, G.; Wang, X.; Sun, P.; Yu, Y.; Zhou, Z.; Wang, Q.; Qian, Y. Enhanced removal of fluoroquinolone antibiotics by peroxydisulfate activated with N-doped sludge biochar: Performance, mechanism and toxicity evaluation Sep. Purif. Technol 2023 , 305 , 122469. [ CrossRef ] 77 Li, C.; Liu, X.; Du, M.; Yang, J.; Lu, Q.; Fu, Q.; He, D.; Zhao, J.; Wang, D. Peracetic acid promotes biohydrogen production from anaerobic dark fermentation of waste activated sludge Sci. Total. Environ 2022 , 844 , 156991. [ CrossRef ] [ PubMed ] 78 Yang, S.; He, C.; Xie, Z.; Li, L.; Xiong, Z.; Zhang, H.; Zhou, P.; Jiang, F.; Mu, Y.; Lai, B. Efficient activation of PAA by FeS for fast removal of pharmaceuticals: The dual role of sulfur species in regulating the reactive oxidized species Water Res 2022 , 217 , 118402. [ CrossRef ] [ PubMed ] 79 Kim, J.; Zhang, T.; Liu, W.; Du, P.; Dobson, J.T.; Huang, C. Advanced oxidation process with peracetic acid and Fe(II) for contaminant degradation Environ. Sci. Technol 2019 , 53 , 13312–13322. [ CrossRef ] 80 Cai, M.; Sun, P.; Zhang, L.; Huang, C. UV/Peracetic acid for degradation of pharmaceuticals and reactive species evaluation Environ. Sci. Technol 2017 , 51 , 14217–14224. [ CrossRef ] 81 Lv, Y.; Zhang, J.; Asgodom, M.; Liu, D.; Xie, H.; Qu, H. Study on the degradation of accumulated bisphenol S and regeneration of magnetic sludge-derived biochar upon microwave irritation in the presence of hydrogen peroxide for application in integrated process Bioresour. Technol 2019 , 293 , 122072. [ CrossRef ] [ PubMed ] 82 Ma, Y.; Zeng, C.; Ding, Y.; Tang, J.; Masek, O.; Deng, Z.; Mu, R.; Zhang, Z. Facile synthesis of ball milling and magnetization co-modified sludge-derived biochar for efficient adsorbing environmental concentration sulfamethoxazole from various waters: Performance and mechanism Sep. Purif. Technol 2024 , 331 , 125584. [ CrossRef ] Disclaimer/Publisher’s Note: The statements, opinions and data contained in all publications are solely those of the individual author(s) and contributor(s) and not of MDPI and/or the editor(s). MDPI and/or the editor(s) disclaim responsibility for any injury to people or property resulting from any ideas, methods, instructions or products referred to in the content.

Other Environmental Sciences Concepts:

[back to top]

Discover the significance of concepts within the article: ‘Recent Progress in Sludge-Derived Biochar and Its Role in Wastewater...’. Further sources in the context of Environmental Sciences might help you critically compare this page with similair documents:

Stability, Incineration, Production process, Physico-chemical properties, Retention time, Heavy metal, Hydrogen bonding, Humic acid, Composting, Chemical properties, Phosphoric acid, Aqueous solution, Adsorption process, Mechanical strength, Porous structure, Tetracycline, Potassium hydroxide, Transition metal, Adsorption capacity, Methylene blue, Environmental Remediation, Molecular oxygen, Phenolic group, Active site, Sodium hydroxide, Molecular structure, Electrostatic attraction, Complexation, Precipitation, Removal efficiency, Effluent Treatment Plant, Advanced oxidation process, Heavy metals removal, Sewage sludge, Surface Charge, Reactive species, Environmental risk, Advanced oxidation processes, Activated carbon, Adsorption, Antibiotic removal, Lignocellulosic biomass, Functional group, Adsorption mechanism, Anaerobic digestion, Organic contaminants, Ball milling, Hydrothermal carbonization, Active substance, Aqueous environment, Environmental pH, H-bonding, Ion exchange, Chemical Coagulation, Inorganic Pollutants, Catalytic performance, Adsorption behavior, Benzene ring, Organic pollutant, Specific surface area, Heterogeneity, Sustainable waste management, Microwave activation, Pore structure, Active oxygen species, Catalytic site, Free radical processes, Chemical precipitation, Inert atmosphere, Activation processes, Zinc compounds, Ultraviolet irradiation, Activated sludge, Potential risk, Coagulation, Specific area, Key factor, Adsorbent material, Sorption, Heating rate, Microporosity, Biochar, Pyrolysis, Pyrolysis temperature, Biochar yield, Pore size distribution, Carbon neutrality, Membrane separation, Sludge, Peracetic acid, Bond interactions, Surface functional group, Water vapor, Production method, Reactive oxygen specie, Contaminant degradation, Secondary pollution, Resource Recovery, Pore filling, Oxygen-containing functional groups, Municipal sludge, Catalytic reaction, Ammonia nitrogen, Heavy metal elements, Wastewater purification, Emerging contaminant, Sludge Treatment, Waste activated sludge, Magnetic biochar, Anaerobically digested sludge, Municipal Sewage Sludge, Municipal Wastewater Treatment Plant, CO2 Capture, Red Mud, Phosphate Adsorption, Sustainable environmental development, Modified biochar, Peroxymonosulfate activation, Sewage sludge biochar, Process mechanism, Removal Mechanism, Tetrabromobisphenol A, Dewatering, Dye pollutants, Fenton catalyst, Layered double hydroxide, Persulfate-based advanced oxidation processes, Ligand Exchange, Ash Removal, Radical pathway, Fenton-like catalyst, Sludge disposal methods, Tetracycline removal, Fenton-like system.